Plotter Repaired

The plotter is pretty much repaired. I just ran through two sets of hull plots for a 65 catamaran. That used up the roll of paper.
I will be able to plot out big full size plots again.
One catch, the new version of the CADD program always prints the over length plots in twice real size, clearly not acceptable. Tech could never fix that so I must revert to older version to plot accurately.
Old version will only run in 15 minute trial version. It stays interesting

No photo description available.

Plotting

The future caught up with me this autumn and I didn’t see it coming. 6 or 7 years ago I bought an amazing plotter. A Canon that could do a page in something like 20 seconds. It could do full size patterns and everything. No more repro copies of an original. It would be just in time printing.  $5000 and supposed to be worth it.
A couple of years ago it stopped working. After about a $1000 in repairs it was working again. Until it quit again and I was warned it would be another $1500 and that might not be enough. That was last year. People were slow to pay at the time, so I parked the plotter. For at least a couple of decades, I could send a dxf file to University Reprographics and they could plot it out at full size.
An overseas job came up that needed that. It turns out that is not possible anymore. To plot AutoCAD, they would need their AutoCAD.
With all of us having plotters, the repro shops had to cut costs. That meant no more AutoCAD at the repro shop. I tried every other repro shop in Seattle. Nobody plots AutoCAD anymore commercially. And even with mere PDFs, it was more than $500 for a hull plot.
So I am getting my plotter fixed. Parts are on the way. I’ll part with the cash. As soon as repairs are done, I can do everyone’s full size pattern plots again.No photo description available.

the Best Weatherstripping

I think that I have tried every kind of weatherstripping to seal door closures or wet hatches. This model, called Rubber seal, ribbed, seems to be the best I have ever tried. All are adhesive backed. The ribs allow one part to deflect, without distorting the whole seal like a square section would. The black one is 3/8″ thick, from Grainger. https://www.grainger.com/product/TRIM-LOK-INC-Rubber-Seal-10D149

The white one is at Home Depot. They don’t carry black. I think is 5/16″ thick.

 

Composite Chainplates

I recently had to review a chainplate on one of my COI cats and send a note to the USCG.
I see from the X-Ray report that the Aolani chainplates were not steel, but composite as I thought they were.
These composite plates are immune to corrosion, unlike metal ones.
I assume the builder used my layup schedule as I have sent earlier. I see no reason to doubt that.
They are easy for the builders to build in a huge safety factor.
Instead of being fastened onto a hull, these synergistically combine to both strengthen the hull and the chainplate.
Unlike the metal plates, these have some resiliency so make all the parts longer lived.
Any delta in the parts from the loads would show up immediately and early by cracks in the paint. Unlike metal plates which usually are not painted.
Attached find a picture of one of my other catamaran designs with composite chainplates. Note that he lifts his entire vessel with only the three chainplate locations.

Visited Ft. Lauderdale

I got to visit my 49′ daycharter cat in Fort Lauderdale . Always one of my favorites. Met captain Jason.
Built mid 90’s by legendary builder, Andre Cocquyt as a composites class project. Students included IBEX presenter, Belle, Blanding.
Still looks good and can be built remotely from assembly.

https://tropicalsailing.com/sailing-charters-fort-lauderdale-spirit-of-lauderdale/?fbclid=IwAR0jIXoj9Se7ALWvKKRZiAFjUndv53sScGF3A0DNgdf_2uRsG6LcjMKntN8

73425100_10157898938913628_4867918243978805248_n

Catamarans, Trimarans, and Kurt Hughes